Your disposal hums but won't spin โ the impeller plate is jammed. It's completely silent when you flip the switch โ the thermal overload protector has tripped or the motor has failed. Water drips from the sink collar โ the sink mounting gasket has deteriorated. Each of these is a different diagnosis, and each has a different solution. Masters Plumbing Service's techs in Stuart, VA arrive with the jamming tools, reset wrench, and replacement units to resolve any disposal failure same visit.
๐ Call +1-855-718-1500 โ Same-Day Service
We carry replacement units on the truck in common horsepower ratings so a same-day swap is possible when the motor has genuinely failed.
A disposal that hums but won't spin almost always just needs the jam cleared with an Allen wrench at the center socket and the reset button pressed โ a 5-minute fix that doesn't require a new unit.
InSinkErator models use a 1/4-inch Allen wrench at the center bottom; Waste King models use a broom-handle approach at the top. Knowing which you have before arriving saves time and prevents the wrong tool damaging the motor shaft.
A disposal that jams once is worth clearing and resetting. A disposal that jams repeatedly, has a seized turntable bearing, emits burning smells, or is over 10 years old is likely approaching motor failure โ and the repair cost of a failed motor exceeds the cost of a new unit.
A disposal installed without properly removing the dishwasher drain knockout plug is a common installation error that floods the dishwasher interior. We check this and correct it if present.
Most disposal calls complete in 30โ60 minutes โ same visit, flat-rate pricing.
If the jam-clearing wrench won't budge the impeller, the motor shaft may be seized rather than just stuck from debris โ we distinguish between the two before recommending replacement.
If power is confirmed at the disposal and it still won't start after a reset, the motor is failed. We then move to the replacement conversation with honest cost comparison.
We identify the leak source before recommending any repair. A sink collar re-seal is a 30-minute job. A unit with a cracked body has no cost-effective repair and warrants replacement.
An unusually loud grinding, rattling, or metal-on-metal sound from a disposal almost always means either a hard object (bottle cap, small utensil, pit from stone fruit) is in the grinding chamber, or an impeller piece has broken and is contacting the shredder ring. We access the grinding chamber safely, remove any foreign objects, and inspect the impeller and shredder ring for damage.
If the slow drain persists after cleaning the drain arm and p-trap, a camera scope of the kitchen drain line is the next step to check for blockage further downstream.
Replacement includes: safely disconnecting electrical at the junction box under the sink, removing the old unit and mounting assembly, installing the new unit with correct wiring and plumbing connections, testing for full jam-free operation, and verifying zero leaks at all connections before leaving.
No guesswork โ we diagnose before we quote, and quote before we start.
Hums but won't spin, completely silent, grinding noise, leaking, or slow to drain โ each symptom tells our dispatcher which tools and possible replacement units to have on the truck. Knowing the disposal brand is a plus but not required.
The tech identifies the failure type in minutes: jam test at the motor socket, reset button check, power confirmation at the wire connections, leak source tracing. We know what each symptom means and we go straight to confirming it.
You decide. We don't upsell replacement when repair is the right answer, and we don't push a cheap repair that won't hold on a unit that's genuinely at end of life.
After repair or replacement, we run the disposal through a full test: several cycles with water running, check under the sink for any drip at all connection points, and confirm the drain arm clears at a normal rate.

The disposal under our kitchen sink was 12 years old and started leaking from the bottom โ which the tech explained is always an internal seal failure, not a repairable condition. He had a replacement 3/4 HP InSinkErator on his truck, installed it in about 45 minutes, and the kitchen is back to normal. Old unit got pulled, new unit tested clean, no leaks at any connection.
Disposal making a loud rattling noise but still grinding. Tech took out a bottle cap that had gotten past the splash guard and was spinning around the grinding chamber. Cleaned out the chamber, confirmed the impeller wasn't damaged, tested for smooth operation. Twenty-minute visit, everything working perfectly.
Old disposal stopped working completely โ no hum, nothing. I assumed the motor failed. The tech checked the wiring first โ found a loose wire nut at the junction box under the sink that had vibrated loose over the years. Reconnected the wire, reset the overload button, disposal came right on. Would have been embarrassing if I'd bought a replacement unit. Masters Plumbing Service's thoroughness saved me a few hundred dollars.

Our trucks carry replacement disposal units in common horsepower ratings for same-day installation when the motor has failed.

Call now โ same-day service available in Stuart and across Stuart, VA.
๐ Call +1-855-718-1500 Now